Displacement of hydraulic pump: 0.82 5gpm (1.1ml/r) Pressure relief valve: 2 2mpa (3200 psi max. relief adjustment for increased lifting power at one port) Rated speed: 285 0r/min Motor voltage: DC12-DV24 Fuel tank: 4L › See more product details; Product description Instructions for use: According to the hydraulic principal charts with clean connection of hydraulic garment unit and oil cylinder hose. Characteristics marked according to the motor and the power of the electromagnetic valve (AC, DC voltage is properly connected.) Centimeter motor observe any abnormal phenomenon. In actuators without load, start the electric, short-term test, check whether all parts are searching, determine and correct step by step after charging normal operation. Precautions: The factory production of a hydraulic engine. When leaving the factory, the system pressure was set. If you want to change, the user is registered according to the actual situation alone through the button to adjust the system pressure, the valve is registered, but no more than the nominal pressure of the system. Check the engine and electromagnetic valve connection carefully. It is strictly prohibited to pick up. When installing and first debugging for the first time, we need to keep the oil level of the internal fuel tank. After a working cycle, the oil tank should be invented, but not too full. Electrical and electromagnetic valve connection should have special attention to the supply features (AC, DC voltage and the same sign. AC motor shell must reliably detect, prohibited ground operation. The motor connection box note water pressure, moisture-proof. Connection for the first time, inching motor check direction from the engine behind, turn counterclockwise. Completely prohibited motor reverse rotation and oil-free idle. When the hydraulic oil needs to be filtered, the filtration accuracy is not lower than 25 microns. The power unit cannot filter the impurities inside the hydraulic cylinder. Therefore, the hydraulic cylinder ink must; Product description Instructions for use: According to the hydraulic principal charts with clean connection of hydraulic garment unit and oil cylinder hose. Characteristics marked according to the motor and the power of the electromagnetic valve (AC, DC voltage is properly connected.) Centimeter motor observe any abnormal phenomenon. In actuators without load, start the electric, short-term test, check whether all parts are searching, determine and correct step by step after charging normal operation. Precautions: The factory production of a hydraulic engine. When leaving the factory, the system pressure was set. If you want to change, the user is registered according to the actual situation alone through the button to adjust the system pressure, the valve is registered, but no more than the nominal pressure of the system. Check the engine and electromagnetic valve connection carefully. It is strictly prohibited to pick up. When installing and first debugging for the first time, we need to keep the oil level of the internal fuel tank. After a working cycle, the oil tank should be invented, but not too full. Electrical and electromagnetic valve connection should have special attention to the supply features (AC, DC voltage and the same sign. AC motor shell must reliably detect, prohibited ground operation. The motor connection box note water pressure, moisture-proof. Connection for the first time, inching motor check direction from the engine behind, turn counterclockwise. Completely prohibited motor reverse rotation and oil-free idle. When the hydraulic oil needs to be filtered, the filtration accuracy is not lower than 25 microns. The power unit cannot filter the impurities inside the hydraulic cylinder. Therefore, the hydraulic cylinder ink must; Instructions for use: According to the hydraulic principal charts with clean connection of hydraulic garment unit and oil cylinder hose. Characteristics marked according to the motor and the power of the electromagnetic valve (AC, DC voltage is properly connected.) Centimeter motor observe any abnormal phenomenon. In actuators without load, start the electric, short-term test, check whether all parts are searching, determine and correct step by step after charging normal operation. Precautions: The factory production of a hydraulic engine. When leaving the factory, the system pressure was set. If you want to change, the user is registered according to the actual situation alone through the button to adjust the system pressure, the valve is registered, but no more than the nominal pressure of the system. Check the engine and electromagnetic valve connection carefully. It is strictly prohibited to pick up. When installing and first debugging for the first time, we need to keep the oil level of the internal fuel tank. After a working cycle, the oil tank should be invented, but not too full. Electrical and electromagnetic valve connection should have special attention to the supply features (AC, DC voltage and the same sign. AC motor shell must reliably detect, prohibited ground operation. The motor connection box note water pressure, moisture-proof. Connection for the first time, inching motor check direction from the engine behind, turn counterclockwise. Completely prohibited motor reverse rotation and oil-free idle. When the hydraulic oil needs to be filtered, the filtration accuracy is not lower than 25 microns. The power unit cannot filter the impurities inside the hydraulic cylinder. Therefore, the hydraulic cylinder ink must
|
![Pack of 10 Dimmable G9 Halogen Bulbs, 40 W 230 V 2800 K G9 Halogen Bulbs for Oven Lamp, Ceiling Lights, Candlesticks [Energy Class F]](https://anete.shop/image/cache/catalog/ext4oc/90/19083374_-9007480-238x238.jpg)
