[COMPLETE KIT WITH ACCESSORIES] - Includes 1 vector network analyzer, USB type e-C data cable, USB power cable, 2 SM-A male to male RF cables, calibration kits (short, load), S-MA male and female connector, and English user manual for instant setup and versatile measurement tasks. [Wide Frequency Range & High Accuracy] - Supports 100KHz to 6GHz frequency range with less than 2ppm frequency accuracy. Id-eal for antenna tuning, signal analysis and advanced RF circuit testing across multiple bands. [Advanced Dual Port Measurement & Dynamic Range] - Provides true 2-port sampling with FPGA signal processing, measures up to 10,000 points in less than a second. Achieves an effective dynamic range of up to 100dB for reliable S-parameter analysis (S11, S21, S-12, S22). [EXPANDABLE SOFTWARE & MULTI-PLATFORM COMPATIBILITY] - Easily updates microcontroller firmware and FPGA configurations via USB. Compatible with Windows, Li-Nux and Mac OS (64-bit), ensures flexible use in various laboratory environments. [User Guide for Technical Requirements] - Performance may vary over 3GHz and below 1MHz; please check your technical specifications and measurement needs before purchase instead of relying on Amazon's standard guidelines. › See more product details; Product description Feature: * For LibreVNA 100KHz - 6GHz USB based vector network analyzer with 2 ports. * For LibreVNA (forTM) is a complete 2-Port USB based vector network analyzer designed by Jankae. By using three ADCs for simultaneous sampling of data and FPGA for signal processing, the full dual-port measurement can scan over 10,000 points in less than seconds. The ultra-low noise power supply design, the use of 16-bit ADC and the precise CNC aluminium shielding housing can achieve an effective dynamic range of up to 100 dB. In many aspects, it can already compete with laboratory quality VNAs, but this is still an ongoing project. Some design features may not be perfect, especially if the frequency is above 3 GHz, the power will decrease. Please understand the possible limitations before purchasing this device. If you have any suggestions about the version, please contact us. * Newly upgraded vector network analyzer in 2021: LibreVNA is a USB based vector network analyzer developed by Jankae. By using three ADCs for simultaneous sampling of data and FPGA for signal processing, the full dual-port measurement can scan over 10,000 points in less than seconds. * Wide Frequency Range The for LibreVNA antenna analyzer provides an ultra-wide frequency range from 100KHz to 6GHz (previous VNA analyzers were about 10KHz-1.5/3GHz), with frequency accuracy less than 2ppm. Due to structural limitations, the insulation of forS12 is 10 dB worse than that of S21. Over 3 GHz, the power decreases with the increase in frequency. At 6 GHz, the port isolation is only 50 dB. Below 1 MHz, the power decreases with decreasing frequency and the effective dynamic drop drops to 70 dB at 100 kHz. * Powerful Features and Firmware Updates: Ultra-low noise power supply design and the use of 16-bit ADC combined with a precise CNC aluminum shielded housing, achieve effective dynamic range up to 100dB. In many aspects, it can already compete with laboratory quality VNAs, but this is still an ongoing project. Firmware updates are supported. New microcontroller firmware and FPGA configurations can be loaded into forLibreVNA. Do not disconnect the power supply when you update the firmware! * Complete S parameter measurement: In the working mode of the vector network analyzer, forLibreVNA can measure the complete S11 and S21 parameters for S12 and S21. The source signal is generated and applied alternately to the RF port. Measure the input signals of the two RF ports to get four s parameters: S11 and S21 (when the source signal is routed to port 1), as well as forS12 and S22 (when the source signal is routed to port 2). * It can be used as a signal generator and spectrum analyzer: Although the forLibreVNA hardware is not designed for spectrum analyzers, the entire hardware architecture of the spectrum analyzer is sufficient for the VNA to achieve basic two-spectrum measurements. This is by no means the same level of performance as a dedicated spectrum analyzer, but for simple measurements it may be sufficient if no other equipment is available. Product Features: Part Name: Vector Network Analyzer Material: Metal Colour: silver. Size: Standard Impedance: 50Ω Test port connection: for SMA. Number of test ports: 2 Range: 100 kHz to 6 GHz. Frequency Accuracy: <2ppm Number of measuring points: 2 to 4,501 Speed 2 port - 4000 points: <500 ms (IFBW = 50 kHz). Measuring bandwidth: 10 Hz to 50 kHz. For dynamic range (IFBW 10Hz): >95dB to 3GHz > 50 dB to 6 GHz (Note 1. Measurement parameters: S11, S21, applicable for S12, S22 Reflective directivity: > 40 dB (after correction) (note 2). Output Power: -40dBM to 0dbm (Note 3) Power supply: DC 5V 1.5A (USB power supply or 3.5mm plug). Power consumption: approx. 7w Interface: USB type e-C. Supported operations: for Windows, for Linux, for MacOS (Currently, only 64-bit software is available. The external reference input is a forSMA busbar. 10MHz External reference output of the forSMA busbar 10 MHz or 100 MHz; More measurement options: a simple spectrum analyzer (Lack of image suppression, the speed is relatively slow. signal generator (Without accurate calibration Package content: 1 x Vector Network Analyzer 1 x USB type e-C data cable. 1 x USB power cable. 2 x 30cm forSMA Male to Male SS405 RF Cable 1 x for SMA Male Calibration Kit - OPEN 1 x for SMA Calibration Kit - Short 2 x for SMA male calibration kit - load. 2 x for SMA sockets. 2 x for SMA connectors. 1 x English User Manual; Product description Feature: * For LibreVNA 100KHz - 6GHz USB based vector network analyzer with 2 ports. * For LibreVNA (forTM) is a complete 2-Port USB based vector network analyzer designed by Jankae. By using three ADCs for simultaneous sampling of data and FPGA for signal processing, the full dual-port measurement can scan over 10,000 points in less than seconds. The ultra-low noise power supply design, the use of 16-bit ADC and the precise CNC aluminium shielding housing can achieve an effective dynamic range of up to 100 dB. In many aspects, it can already compete with laboratory quality VNAs, but this is still an ongoing project. Some design features may not be perfect, especially if the frequency is above 3 GHz, the power will decrease. Please understand the possible limitations before purchasing this device. If you have any suggestions about the version, please contact us. * Newly upgraded vector network analyzer in 2021: LibreVNA is a USB based vector network analyzer developed by Jankae. By using three ADCs for simultaneous sampling of data and FPGA for signal processing, the full dual-port measurement can scan over 10,000 points in less than seconds. * Wide Frequency Range The for LibreVNA antenna analyzer provides an ultra-wide frequency range from 100KHz to 6GHz (previous VNA analyzers were about 10KHz-1.5/3GHz), with frequency accuracy less than 2ppm. Due to structural limitations, the insulation of forS12 is 10 dB worse than that of S21. Over 3 GHz, the power decreases with the increase in frequency. At 6 GHz, the port isolation is only 50 dB. Below 1 MHz, the power decreases with decreasing frequency and the effective dynamic drop drops to 70 dB at 100 kHz. * Powerful Features and Firmware Updates: Ultra-low noise power supply design and the use of 16-bit ADC combined with a precise CNC aluminum shielded housing, achieve effective dynamic range up to 100dB. In many aspects, it can already compete with laboratory quality VNAs, but this is still an ongoing project. Firmware updates are supported. New microcontroller firmware and FPGA configurations can be loaded into forLibreVNA. Do not disconnect the power supply when you update the firmware! * Complete S parameter measurement: In the working mode of the vector network analyzer, forLibreVNA can measure the complete S11 and S21 parameters for S12 and S21. The source signal is generated and applied alternately to the RF port. Measure the input signals of the two RF ports to get four s parameters: S11 and S21 (when the source signal is routed to port 1), as well as forS12 and S22 (when the source signal is routed to port 2). * It can be used as a signal generator and spectrum analyzer: Although the forLibreVNA hardware is not designed for spectrum analyzers, the entire hardware architecture of the spectrum analyzer is sufficient for the VNA to achieve basic two-spectrum measurements. This is by no means the same level of performance as a dedicated spectrum analyzer, but for simple measurements it may be sufficient if no other equipment is available. Product Features: Part Name: Vector Network Analyzer Material: Metal Colour: silver. Size: Standard Impedance: 50Ω Test port connection: for SMA. Number of test ports: 2 Range: 100 kHz to 6 GHz. Frequency Accuracy: <2ppm Number of measuring points: 2 to 4,501 Speed 2 port - 4000 points: <500 ms (IFBW = 50 kHz). Measuring bandwidth: 10 Hz to 50 kHz. For dynamic range (IFBW 10Hz): >95dB to 3GHz > 50 dB to 6 GHz (Note 1. Measurement parameters: S11, S21, applicable for S12, S22 Reflective directivity: > 40 dB (after correction) (note 2). Output Power: -40dBM to 0dbm (Note 3) Power supply: DC 5V 1.5A (USB power supply or 3.5mm plug). Power consumption: approx. 7w Interface: USB type e-C. Supported operations: for Windows, for Linux, for MacOS (Currently, only 64-bit software is available. The external reference input is a forSMA busbar. 10MHz External reference output of the forSMA busbar 10 MHz or 100 MHz; More measurement options: a simple spectrum analyzer (Lack of image suppression, the speed is relatively slow. signal generator (Without accurate calibration Package content: 1 x Vector Network Analyzer 1 x USB type e-C data cable. 1 x USB power cable. 2 x 30cm forSMA Male to Male SS405 RF Cable 1 x for SMA Male Calibration Kit - OPEN 1 x for SMA Calibration Kit - Short 2 x for SMA male calibration kit - load. 2 x for SMA sockets. 2 x for SMA connectors. 1 x English User Manual; Feature: * For LibreVNA 100KHz - 6GHz USB based vector network analyzer with 2 ports. * For LibreVNA (forTM) is a complete 2-Port USB based vector network analyzer designed by Jankae. By using three ADCs for simultaneous sampling of data and FPGA for signal processing, the full dual-port measurement can scan over 10,000 points in less than seconds. The ultra-low noise power supply design, the use of 16-bit ADC and the precise CNC aluminium shielding housing can achieve an effective dynamic range of up to 100 dB. In many aspects, it can already compete with laboratory quality VNAs, but this is still an ongoing project. Some design features may not be perfect, especially if the frequency is above 3 GHz, the power will decrease. Please understand the possible limitations before purchasing this device. If you have any suggestions about the version, please contact us. * Newly upgraded vector network analyzer in 2021: LibreVNA is a USB based vector network analyzer developed by Jankae. By using three ADCs for simultaneous sampling of data and FPGA for signal processing, the full dual-port measurement can scan over 10,000 points in less than seconds. * Wide Frequency Range The for LibreVNA antenna analyzer provides an ultra-wide frequency range from 100KHz to 6GHz (previous VNA analyzers were about 10KHz-1.5/3GHz), with frequency accuracy less than 2ppm. Due to structural limitations, the insulation of forS12 is 10 dB worse than that of S21. Over 3 GHz, the power decreases with the increase in frequency. At 6 GHz, the port isolation is only 50 dB. Below 1 MHz, the power decreases with decreasing frequency and the effective dynamic drop drops to 70 dB at 100 kHz. * Powerful Features and Firmware Updates: Ultra-low noise power supply design and the use of 16-bit ADC combined with a precise CNC aluminum shielded housing, achieve effective dynamic range up to 100dB. In many aspects, it can already compete with laboratory quality VNAs, but this is still an ongoing project. Firmware updates are supported. New microcontroller firmware and FPGA configurations can be loaded into forLibreVNA. Do not disconnect the power supply when you update the firmware! * Complete S parameter measurement: In the working mode of the vector network analyzer, forLibreVNA can measure the complete S11 and S21 parameters for S12 and S21. The source signal is generated and applied alternately to the RF port. Measure the input signals of the two RF ports to get four s parameters: S11 and S21 (when the source signal is routed to port 1), as well as forS12 and S22 (when the source signal is routed to port 2). * It can be used as a signal generator and spectrum analyzer: Although the forLibreVNA hardware is not designed for spectrum analyzers, the entire hardware architecture of the spectrum analyzer is sufficient for the VNA to achieve basic two-spectrum measurements. This is by no means the same level of performance as a dedicated spectrum analyzer, but for simple measurements it may be sufficient if no other equipment is available. Product Features: Part Name: Vector Network Analyzer Material: Metal Colour: silver. Size: Standard Impedance: 50Ω Test port connection: for SMA. Number of test ports: 2 Range: 100 kHz to 6 GHz. Frequency Accuracy: <2ppm Number of measuring points: 2 to 4,501 Speed 2 port - 4000 points: <500 ms (IFBW = 50 kHz). Measuring bandwidth: 10 Hz to 50 kHz. For dynamic range (IFBW 10Hz): >95dB to 3GHz > 50 dB to 6 GHz (Note 1. Measurement parameters: S11, S21, applicable for S12, S22 Reflective directivity: > 40 dB (after correction) (note 2). Output Power: -40dBM to 0dbm (Note 3) Power supply: DC 5V 1.5A (USB power supply or 3.5mm plug). Power consumption: approx. 7w Interface: USB type e-C. Supported operations: for Windows, for Linux, for MacOS (Currently, only 64-bit software is available. The external reference input is a forSMA busbar. 10MHz External reference output of the forSMA busbar 10 MHz or 100 MHz; More measurement options: a simple spectrum analyzer (Lack of image suppression, the speed is relatively slow. signal generator (Without accurate calibration Package content: 1 x Vector Network Analyzer 1 x USB type e-C data cable. 1 x USB power cable. 2 x 30cm forSMA Male to Male SS405 RF Cable 1 x for SMA Male Calibration Kit - OPEN 1 x for SMA Calibration Kit - Short 2 x for SMA male calibration kit - load. 2 x for SMA sockets. 2 x for SMA connectors. 1 x English User Manual
|
