HIGHLY ACCURATE ALIGNMENT Perfect for CNC spindle alignment tools that require precise edge and center detection with ±X, ±Y, +Z approach for reliable calibration DURABLE PERFORMANCE Stainless steel probe and aluminum alloy accessories provide high wear resistance, support over 3 million trigger cycles for consistent operation QUICK SETUP & COMPATIBILITY Compatible with most desktop CNC machines, easy cable identification with VCC, GND, IO wiring for simplified installation REPEATABLE MEASUREMENTS Maintains feed speed at 50-200mm/min to ensure consistent probe positioning and reduce measurement errors COMPACT DESIGN FOR MULTI-DIRECTIONAL USE The silver TP06 model works in multiple directions, fits tight spaces and various CNC testing applications › See more product details; Product description Feature: NO: normally open. N-C: normally closed. Precautions: 1. Need to turn on the spindle speed? Never, never, never. 2. How to distinguish these three cables? The red wire is VCC, the black wire is GND, and the white wire is IO. 3. Is the concentricity of the probe different with each installation? Because its ER chuck spring clamp cannot guarantee verticality. Every time the probe is installed, even if the concentricity is set to 1 wire, there will still be deviations when the probe is removed and reinstalled. Therefore, it is AAA grade drill chuck with higher for (concentricity <= 0.0 05), as many drill chucks in China have fake standards. It is recommended to use a high gauge or steel rod to check the gauge after installation. Check out the concentricity. It is necessary to place the microns 50 mm away from the drill chuck, which is about the distance between our probe ball head and the root of the tool handle. 4. Is the concentricity still poor when I obviously use an AAA drill chuck? That's because you bought a virtual label lining. Under normal circumstances, when the spindle jumps 0.01, the AAA drill chuck clamps the cutter and workbench tool holder, the error cannot exceed 0.02, and the maximum error cannot exceed 0.03. There will be a slight angle deviation between the center of the tool holder and the center of the spindle, which is increased by the length of the tool holder. Usually the root of the tool is measured with a calibration meter, and no big error can be seen, but since the probe needle is about 50 mm away from the tool holder, the error is more magnified. Therefore, you have to choose a high-for chuck, which is nothing more than a ten dollar difference. Technical data: Part Name: 3D Probe with Cable Material: probe is stainless steel, aluminum alloy accessories Size: as shown in the picture. Color: Silver Model: TP06. Direction: ±X, ±Y, +Z Repeatability: <0.01mm Feed speed: 50-200 mm/min. Crossing for protective distance: XY ± 4 mm, Z +2 mm. Reliability: the service life is more than 3 million triggers Power supply: DC 5~24V Package includes: A: 6mm Edge Finder + 1 x Wire + 1 x Wrench (N-C, not optional) B: 4mm Edge Finder (NO) + 1 x Wire + 1 x Wrench C: Needle Holder D: probe.; Product description Feature: NO: normally open. N-C: normally closed. Precautions: 1. Need to turn on the spindle speed? Never, never, never. 2. How to distinguish these three cables? The red wire is VCC, the black wire is GND, and the white wire is IO. 3. Is the concentricity of the probe different with each installation? Because its ER chuck spring clamp cannot guarantee verticality. Every time the probe is installed, even if the concentricity is set to 1 wire, there will still be deviations when the probe is removed and reinstalled. Therefore, it is AAA grade drill chuck with higher for (concentricity <= 0.0 05), as many drill chucks in China have fake standards. It is recommended to use a high gauge or steel rod to check the gauge after installation. Check out the concentricity. It is necessary to place the microns 50 mm away from the drill chuck, which is about the distance between our probe ball head and the root of the tool handle. 4. Is the concentricity still poor when I obviously use an AAA drill chuck? That's because you bought a virtual label lining. Under normal circumstances, when the spindle jumps 0.01, the AAA drill chuck clamps the cutter and workbench tool holder, the error cannot exceed 0.02, and the maximum error cannot exceed 0.03. There will be a slight angle deviation between the center of the tool holder and the center of the spindle, which is increased by the length of the tool holder. Usually the root of the tool is measured with a calibration meter, and no big error can be seen, but since the probe needle is about 50 mm away from the tool holder, the error is more magnified. Therefore, you have to choose a high-for chuck, which is nothing more than a ten dollar difference. Technical data: Part Name: 3D Probe with Cable Material: probe is stainless steel, aluminum alloy accessories Size: as shown in the picture. Color: Silver Model: TP06. Direction: ±X, ±Y, +Z Repeatability: <0.01mm Feed speed: 50-200 mm/min. Crossing for protective distance: XY ± 4 mm, Z +2 mm. Reliability: the service life is more than 3 million triggers Power supply: DC 5~24V Package includes: A: 6mm Edge Finder + 1 x Wire + 1 x Wrench (N-C, not optional) B: 4mm Edge Finder (NO) + 1 x Wire + 1 x Wrench C: Needle Holder D: probe.; Feature: NO: normally open. N-C: normally closed. Precautions: 1. Need to turn on the spindle speed? Never, never, never. 2. How to distinguish these three cables? The red wire is VCC, the black wire is GND, and the white wire is IO. 3. Is the concentricity of the probe different with each installation? Because its ER chuck spring clamp cannot guarantee verticality. Every time the probe is installed, even if the concentricity is set to 1 wire, there will still be deviations when the probe is removed and reinstalled. Therefore, it is AAA grade drill chuck with higher for (concentricity <= 0.0 05), as many drill chucks in China have fake standards. It is recommended to use a high gauge or steel rod to check the gauge after installation. Check out the concentricity. It is necessary to place the microns 50 mm away from the drill chuck, which is about the distance between our probe ball head and the root of the tool handle. 4. Is the concentricity still poor when I obviously use an AAA drill chuck? That's because you bought a virtual label lining. Under normal circumstances, when the spindle jumps 0.01, the AAA drill chuck clamps the cutter and workbench tool holder, the error cannot exceed 0.02, and the maximum error cannot exceed 0.03. There will be a slight angle deviation between the center of the tool holder and the center of the spindle, which is increased by the length of the tool holder. Usually the root of the tool is measured with a calibration meter, and no big error can be seen, but since the probe needle is about 50 mm away from the tool holder, the error is more magnified. Therefore, you have to choose a high-for chuck, which is nothing more than a ten dollar difference. Technical data: Part Name: 3D Probe with Cable Material: probe is stainless steel, aluminum alloy accessories Size: as shown in the picture. Color: Silver Model: TP06. Direction: ±X, ±Y, +Z Repeatability: <0.01mm Feed speed: 50-200 mm/min. Crossing for protective distance: XY ± 4 mm, Z +2 mm. Reliability: the service life is more than 3 million triggers Power supply: DC 5~24V Package includes: A: 6mm Edge Finder + 1 x Wire + 1 x Wrench (N-C, not optional) B: 4mm Edge Finder (NO) + 1 x Wire + 1 x Wrench C: Needle Holder D: probe.
|
![Pack of 10 Dimmable G9 Halogen Bulbs, 40 W 230 V 2800 K G9 Halogen Bulbs for Oven Lamp, Ceiling Lights, Candlesticks [Energy Class F]](https://anete.shop/image/cache/catalog/ext4oc/90/19083374_-9007480-238x238.jpg)
